HealthRider HRSY23080 Manuale Utente

¨USERÕS MANUALModel No. HRSY23080Serial No. The serial number is found in thelocation shown below. Write theserial number in the space above.CAUTIONRe

1717. Leg Lever Assembly. Attach a Bumper (40) to theSeat Frame (7) with a #8 x 1Ó Screw (78).Press a 2Ó Square Inner Cap (28) into the indicatedend o

1123. Feed the end of the Low Cable (72) through the indi-cated slot in the Weight Upright (2) from above.Wrap the Low Cable (72) around a 3 1/2Ó Pull

1226. Route the end of the High Cable (73) with the loopthrough the bracket on the Main Upright (1) fromabove. Route the High Cable over a 3 1/2Ó Pull

1329. Wrap the High Cable (73) around a 3 1/2Ó Pulley (24)in the direction shown.Attach the 3 1/2Ó Pulley (24) to the bracket on theStabilizer (4) wit

1433. Wrap the High Cable (73) around a 3 1/2Ó Pulley (24)in the direction shown.Attach the 3 1/2Ó Pulley (24) and a Cable Trap (25) tothe riser on th

1536. Route the High Cable (73) through the slot in the legof the Seat Frame (7).Attach the closed loop at the end of the High Cable(73) to the Leg Le

164021191789486840. Important: Follow all three Cables from end toend and make sure they rest in the grooves of allPulleys and that both the Cables an

1744. Press two 3/4Ó Round Inner Caps (43) into each PadTube (42). Insert one Pad Tube (42) into the Seat Frame (7).Slide a Foam Roller (30) onto each

184848. The decal shown below has been attached to the home gym system in the location shown. If the decal ismissing or illegible, please call our cus

19Cable DiagramThe Cable Diagrams below show the proper routing of the Butterfly Cable (92), the High Cable (73) and the LowCable (72). The numbers sh

2Important Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20Attaching the Lat Bar, Ankle Strap or AbStrap to the High Pulley StationAttach the Lat Bar (61) to the High Cable (73) with aCable Clip (69). For so

Coordinating the Positions of the Backrestand Press FrameFor many exercises, the Press Frame (8) and theBackrest (12) must be in the correct positions

22Adjusting the Butterfly ArmsMake sure the Backrest (12) is in the horizontal positionas described on the previous page. Pull out theAdjustment Knob

23Tightening the CablesWoven cable, the type of cable used on the home gymsystem, can stretch slightly when it is first used. If there isslack in the

3/4" Round Inner Cap (43)3/4Ó Dome Cap (82)5/8Ó x 1/2Ó Bushing (85)1/2Ó x 3/4Ó Bushing (76)1/2Ó x 3/8Ó Bushing (83)5/8Ó x 1Ó Bushing (86)5/8Ó x 1

3/8" Nylon Locknut (50)3/8" Nylon Jamnut (63)1/4" x 1 1/2" Bolt (95)5/16" Nylon Locknut (64)#8 x 1Ó Screw (78)3/8" x 1 1

3/8" x 3 1/2" Bolt (56)3/8" x 4 3/4" Bolt (46)3/8" x 2 3/4" Bolt (47)3/8" x 2 3/4" Carriage Bolt (45)3/8"

Note: Ò#Ó indicates a non-illustrated part. Specifications are subject to change without notice. 1 1 Main Upright2 1 Weight Upright3 1 Support Upright

3043904949407853417330432850474243302863424330901350 7 64556502550244750503839503710165651255539124256344144483234955554646553224554785855055257595050

Ordering Replacement PartsLimited WarrantyTo order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Mondayt

3ASSEMBLED DIMENSIONS: Height: 81 in.Width: 54 in. Length: 67 in. Low PulleyStationFoot PlateLegLeverButterflyArmPress ArmsShroudCovering Weight Stack

4Note: This introduction will save you moretime than it takes to read it!Identifying PartsTo help you identify the small parts used in assem-bly, we h

1. Before beginning, make sure that you have readand understood the information on page 4.Locate and open the parts bag labeled ÒFRAMEASSEMBLY.ÓInsert

4. Place the bracket on the lower end of the MainUpright (1) over the indicated 3/8Ó x 2 3/4Ó CarriageBolts (45) in the Stabilizer (4). Hand tighten t

9. Place the bracket on the lower end of the WeightUpright (2) over the indicated 3/8Ó x 2 3/4Ó CarriageBolts (45) in the Weight Base (5). Hand tight

812. Attach the upper ends of the Weight Guides (15) tothe welded bracket underneath the Weight Upright (2)with two 3/8Ó x 1 3/4Ó Bolts (57) and two 3

14. Tap two 1Ó Retainer Rings (32) and a 1Ó Round CoverCap (81) onto one end of the Press Frame Tube (34).Lubricate the Press Frame Tube in its entire